ELP

Bus wire	Copper
1st insulation	Fluoropolymer
Heating conductor	Heating conductor alloy
2nd insulation	Fluoropolymer
Protective braid	Copper, nickel-plated
Outer jacket	Fluoropolymer

Constant wattage trace heater with resistance wire a

These parallel trace heaters offer tremendous flexibility in use, as they can easily be cut to the required length off the roll, with the assurance of constant power output. There is no need for a connecting cable and input can be unilateral. It is quick and easy to assemble, this saves a lot of time, and reduces costs considerably as a result. Since output of up to 60 W٫m is possible for lengths laid to piping, ELP parallel trace heaters are particularly suitable for piping with high output requirements such as in industrial process technology

The particularly temperature-resistant outer shell in Fluoropolymer and the high level of chemical resistance of the Fluoropolymer ensure a long useful life.

Checklist

Connection & end termination set
EL-ECP1	Silicone termination cap, transparent; for ELP/PFA up to 200 °C	09112P1
EL-ECP+	Silicone termination cap, red; for ELP/PFA up to 260 °C	09112PP
EL-ECP-Ex	Silicone termination cap, red; for ELP/PFA up to 260 °C, Ex-marking	0X81EP1
ELVB-ELPA-25	Power connection kit, cold assembly, gland M25, PC	091A050
ELVB-ELPEx-25	Power connection kit, cold assembly, gland M25, PE, Ex e	0X81PA2
ELVB-ELPEx-20	Power connection kit, cold assembly, gland M20, brass, Ex d e	0X81PPD
ELVB-SRV-ELP	Splice kit, shrink fit	0911118

Chemistry and Petrochemistry

Bullaing construction

Food Processing Industry

Paper industry

Benefits

Single end power input

Can be cut to length

Constant power output per meter

High chemical resistanice

UV-resitance

Trace Heater classification

1126 Ex 60079-30-1 IC Gb

120 Ex 60079-30-1CD6

System classificationi

II 2G Ex 60079-30-1 IIC 16.12 Gh

2D Ex 60079-30-1 С Тxx°С. Пъ

Certification

IECE EPS 12.0009 U

IECEX EPS 21.0062 X

EPS 12 ATEX 1438 บ

EPS 21 ATEX 1198 X

Technical Information
Maximum withstand temperature	260 °C
Nominal voltage	230 VAC up to 277 VAC*
Max. Current	40 A
Min. Bending radius	25 mm
Min. installation temperature	– 60 °C
Min. start up temperature	– 60 °C
Cross section bus wire	2 x 1.5 mm²; (2 x 4.0 mm² on request)

NOTE

> Heating circuit lengths ELP٫PFA on the following conditions:

16 A circuit breaker, 80% utilisation, start up temp. 10 deg * C

> Max. 1096 voltage drop

> Power connection to one (1) heater end

> Greater lengths are possible with higher rated circuit breakers please contact eltherm

> Cables shall neither intersect nor contact,

> Provide protection by means of circuit breaker RCO 30 mA,

> Please observe the standaris

IEC-62395-2, EN 60519-10, EN 62395-2

Heating circuit length
Type	Power [W/m]	Length @ start up temp. [m]
ELP/PFA 15 BOT	15.0	184.0
ELP/PFA 30 BOT	30.0	100.0
ELP/PFA 45 BOT	45.0	66.0
ELP/PFA 60 BOT	60.0	50.0

Ordering information
Type	Nominal power	Maintain temperature * max	Dimmensions for 1,5 mm² approx. [mm]	Contact spacing [m]	Weight (1,5mm²) approx. [g/m]	Article - No. approx. [g/m]
ELP/PFA 15 BOT	200 °C	8.6 x 6.7	1.0	1.0	120	B0332015

Checklist

NOTE

تماس با ما